Forumi


Povratak   PC Ekspert Forum > Internet i mrežne tehnologije > Mreže
Ime
Lozinka

Odgovori
 
Uređivanje
Staro 16.01.2023., 18:15   #1
Nikky
Moderator
 
Nikky's Avatar
 
Datum registracije: Sep 2006
Lokacija: St
Postovi: 23,073
Arrow Power over Ethernet - pitanja i odgovori

Tu i tamo netko pita šta i kako pa se zagubi među temama,
evo jedna tema baš za Power over Ethernet ili ti ga PoE.

Za uvod evo šta kaže wikipedia: Power over Ethernet

E sad, kako implementacija nije baš crno - bijelo nego prije neka nijansa sive

Čak i ako se pazi na detalje (sitna slova), do problema ili ne kompatibilnosti može doći, a u najgorem slučaju i do bijelog dima

Slučajno naletio na jedan txt / post sa dobrom "rekapitulacijom":

My current understanding and suggestion to anyone getting PoE stuff:
  • Terms 'Active PoE' and 'Passive PoE' are useless, do not trust them. They are undefined terms, and people use them to mean whatever they want.
    Even 'PoE' itself does not refer to any standard, just to the idea of using Ethernet cabling, somehow, for power delivery.
  • Look at the exact product datasheet or manual, and check for explicit mention of compliance with
    • IEEE 802.3af (15.4 W)
    • IEEE 802.3at (25.5 W)
    • IEEE 802.3bt (71.3 W)
    to find out if the device. A compliant supply (PSE) will not destroy any non-PoE device connected to a powered port.
  • 10Base-T and 100Base-T use only two out of the four twisted pairs in an Ethernet cable for data transfers: pins 1 (Tx+), 2 (Tx-), 3, (Rx+), and 6 (Rx-). The two other pairs (4, 5, 7, 8) are unused.
  • 1000Base-T and faster uses all four twisted pairs in an Ethernet cable dor data.
  • IEEE 802.3af and 802.3at have three different modes:
    • Mode A: uses two twisted pairs for power, pins 1, 2, 3, 6
    • Mode B: uses two twisted pairs for power, pins 4, 5, 7, 8
    • Mode C: uses all four twisted pairs for power; often called '4PPoE'
    Supplies (PSEs) detect the support of devices (PD), and only provide 48V if the device has the signature of a proper 802.3af/at device. The polarity (between pairs) may vary.
  • The signature for a powered IEEE 802.3af or 802.3at device (PD) is a 24.9k kΩ 1% between the twisted pair (1,2) and (3,6) for mode A, between twisted pair (4,5) and (7,8) for mode B, and both for mode C.
  • IEEE 802.3af and 802.3at 'negotiation' is basically just the detection of the presence of this resistance at low enough voltages and currents to not destroy common devices with just 150Ω of resistance between pairs due to 75Ω termination to ground.
    There are chips like LTC4267 (802.3af/at) and LTC4295 (802.3af/at/bt) that handle that detection; such datasheets describe how it is done.
  • It is stuffing 48V without checking, to ordinary Ethernet devices that causes the connector or circuitry to blow by trying to dissipate several watts of heat within the tiny connector or a small termination resistors, that breaks things.
    Standards-compliant PSEs do not break ordinary Ethernet devices; and PDs used on ordinary Ethernet behave just like ordinary Ethernet devices.
  • Ethernet cables themselves should have less than 100Ω DC resistance, but non-copper cabling (CCA, copper-clad aluminium, and similar) may have much higher resistance and fail for power delivery, even though they seem to carry data mostly fine.
    Expected DC resistances for proper <10m copper Ethernet cables, measured using an ordinary cheap multimeter, per wire, are in the 1Ω to 5Ω.
  • I am not exactly sure of the IEEE 802.3bt 'negotiation', but it is backwards compatible with 802.3af and 802.3at. It adds new power classes and 'stuff' for the higher power support.
  • Manufacturers do not seem to agree whether a 802.3af or 802.3at supply equipment (PSE) or powered device (PD) should support more than one mode or not. Some do, some do not. So, just because both devices are compliant with 802.3af/at, does not mean they will for sure work with together, if it happens one is mode A only and the other is mode B only.
  • There exist supplies ('injectors') that work with 10BaseT and 100BaseT Ethernet cabling, using the unused two pairs for power delivery using various voltages, often 24V or 48V. These do not do any kind of detection or negotiation, and usually just treat the unused pairs as DC voltage lines.
    They are not compatible with IEEE 802.3af/at/bt supplies (PSEs) and usually not even devices (PDs), and will easily destroy standard Ethernet ports.
  • There exist supplies ('injectors') that work with 10/100/1000 Ethernet, using magnetics but simply biasing the pairs at different voltages for power delivery.
    These do not do any kind of detection or negotiation either, and usually just treat the unused pairs as DC voltage lines.
    They are not compatible with IEEE 802.3af/at/bt supplies (PSEs) and usually not even devices (PDs), and will easily destroy standard Ethernet ports.
    MikroTik devices often support being powered via such, but since there is no standard, be sure to check the compatibility thoroughly, and label such cabling so that nobody confuses them for normal Ethernet cabling.
izvor > https://www.eevblog.com/forum/networ...73/#msg4560673

Još jedan pregled (šta / kako / zašto): What is PoE?

Toliko za početak

Zadnje izmijenjeno od: Nikky. 16.01.2023. u 19:59.
Nikky je offline   Reply With Quote
Oglas
 
Oglas
Oglas Oglasni prostor

Odgovori


Uređivanje

Pravila postanja
Vi ne možete otvarati nove teme
Vi ne možete pisati odgovore
Vi ne možete uploadati priloge
Vi ne možete uređivati svoje poruke

BB code je Uključeno
Smajlići su Uključeno
[IMG] kod je Uključeno
HTML je Uključeno

Idi na