Uspješno sam overklokirao procesor i memoriju i sve je radilo stabilno na 3.93 ghz, a memorija na 1042 Mhz. Sve je bilo uredo dok najedanput matična ploča nije sve postavke vratila na default-ne. U MB intelligent tweakeru postavke su ostale kakve sam i postavio, samo što CPUZ i screen prilikom boot-anja pokazuje default-ne vrijednosti E8400@3.00 (333x9) a prije je bilo i trebalo bi biti E8400@3.93 (436x9). Dakle matična proča više ne reagira na moj input u biosu te drži tajminge procesora na default-nim vrijednostima, dok tajminge memorije mogu modificirati. Nisam nov u overklokiranju, upoznat sam sa svim postupcima kao i dopuštenim voltažama te ni u jednom trenutku,prilikom overklokiranja, nisam izašao iz okvira dopuštenih i preporučenih vrijednosti. Do sada sam pokušao skoro pa sve što sam mogao uključujuči flash-anje biosa sa više verzija ali problem ostaje.
Moje je pitanje dali je moguće da je to hardverski problem ili je stvar u biosu?
Evo mojih postavka u tweakeru:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Turbo
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................: 0
CPU Frequency ...........................: 3.93ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [enabled]
CPU Host Frequency (Mhz) ............: 436Mhz
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: disabled
(G)MCH Frequency Latch...............: [aUTO]
System Memory Multiplier ..............: 3.00A
Memory Frequency (Mhz) ..............: 1046
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................: 5
tRAS..........................................: 15
Advanced Timing Control
tRRD...........................................:4
tWTR..........................................:6
tWR............................................:6
tRFC...........................................:60
tRTP...........................................:5
Command Rate (CMD) ....................:2
Channel A
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
Voltage Type.………... auto
CPU
CPU Vcore….……….........................: 1.30
CPU Termination….............:1.24
CPU PLL…………………...........:1.50
CPU Referen.…………...........:auto
CPU Reference2………..........:auto
MCH/ICH
MCH Core……………...............: 1.26
MCH Reference….……............:auto
MCH/DRAM Ref.….................:auto
ICH I/O………………................:1.55
ICH Core…………...…............:1.14
DRAM
DRAM Voltage ……...............:2.1 V
DRAM Termination .…....... ....:auto
Channel A Reference ............:auto
Channel B Reference ............:auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Enabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Unaprijed hvala na svakoj pomoći.