Imam Mikrotik 2011UiAS-2HnD i optiku od HTa. Danas sam dobio STB i nikako to natjerati da radi, pročitao sam valjda sve i jednu temu ovdje i na redditu što sam našao.
Ovisno o tome u kojem je bridgeu port ether5 gdje je spojen STB, dobijem ili ekran za unos korisničkog ID i PINa (a to ne prolazi, kaže "Dogodila se pogreška") ili kad je u bridge-iptv gdje i mora biti, prvo dobijem x396 pa x397 greške. Gdje sam zeznuo? U prilogu počišćena konfa. Net radi, ONT je spojen na ether1, STB na ether5. Svi ostali portovi osim 9 su za net, na 9 bi trebao doći VoIP.... Tnx!
Code:
# jun/13/2022 00:14:49 by RouterOS 7.2.3
# software id = PGV3-3UNL
#
# model = 2011UiAS-2HnD
/interface bridge
add admin-mac=4C:5E:0C:XX:XX:XX auto-mac=no comment=defconf mtu=1498 name=bridge
add mtu=1500 name=bridge-iptv
/interface vlan
add interface=ether1 mtu=1492 name=vlan100-internet vlan-id=100
add interface=ether1 name=vlan1500-iptv vlan-id=1500
/interface pppoe-client
add add-default-route=yes disabled=no interface=vlan100-internet keepalive-timeout=60 max-mru=1500 max-mtu=1500 \
name=pppoe-out1 service-name=HT user=xxxx@htnet-dsl
/interface list
add comment=defconf name=WAN
add comment=defconf name=LAN
/interface bridge port
add bridge=bridge comment=defconf ingress-filtering=no interface=ether2
add bridge=bridge comment=defconf ingress-filtering=no interface=ether3
add bridge=bridge comment=defconf ingress-filtering=no interface=ether4
add bridge=bridge-iptv comment=defconf ingress-filtering=no interface=ether5
add bridge=bridge comment=defconf ingress-filtering=no interface=ether6
add bridge=bridge comment=defconf ingress-filtering=no interface=ether7
add bridge=bridge comment=defconf ingress-filtering=no interface=ether8
add bridge=bridge comment=defconf ingress-filtering=no interface=ether10
add bridge=bridge comment=defconf ingress-filtering=no interface=sfp1
add bridge=bridge comment=defconf ingress-filtering=no interface=wlan1
add bridge=bridge ingress-filtering=no interface=wlan2
add bridge=bridge interface=ether9
add bridge=bridge-iptv interface=vlan1500-iptv
/interface bridge settings
set use-ip-firewall=yes
/ip neighbor discovery-settings
set discover-interface-list=LAN
/ip settings
set max-neighbor-entries=8192
/ipv6 settings
set disable-ipv6=yes max-neighbor-entries=8192
/interface list member
add comment=defconf interface=bridge list=LAN
add comment=defconf interface=ether1 list=WAN
add interface=pppoe-out1 list=WAN
/ip firewall filter
add action=accept chain=input comment=maxTV protocol=igmp
Probao sam i ovako, da portovi (ether5 i vlan1500-iptv) imaju PVID ali nije pomoglo...
Code:
/interface bridge port
add bridge=bridge comment=defconf ingress-filtering=no interface=ether2
add bridge=bridge comment=defconf ingress-filtering=no interface=ether3
add bridge=bridge comment=defconf ingress-filtering=no interface=ether4
add bridge=bridge-iptv comment=defconf interface=ether5 pvid=1500
add bridge=bridge comment=defconf ingress-filtering=no interface=ether6
add bridge=bridge comment=defconf ingress-filtering=no interface=ether7
add bridge=bridge comment=defconf ingress-filtering=no interface=ether8
add bridge=bridge comment=defconf ingress-filtering=no interface=ether10
add bridge=bridge comment=defconf ingress-filtering=no interface=sfp1
add bridge=bridge comment=defconf ingress-filtering=no interface=wlan1
add bridge=bridge ingress-filtering=no interface=wlan2
add bridge=bridge interface=ether9
add bridge=bridge-iptv interface=vlan1500-iptv pvid=1500
Palio sam i filtering na tom bridge-iptv, niti to nije pomoglo...
Code:
add mtu=1500 name=bridge-iptv pvid=1500 vlan-filtering=yes