[Miha-Đakovo]

Pitanje iz naslova.... Hvala!!

Evo u manualu piše ovako:

4-1-4 Configuring SATA Hard Drive(s)

To configure SATA hard drive(s), follow the steps below:

(1) Install SATA hard drive(s) in your system.
(2) Configure SATA controller mode and boot sequence in BIOS Setup.
(3)* Configure RAID set in RAID BIOS.
(4) Make a floppy disk containing the SATA controller driver.
(5) Install the SATA controller driver during OS installation.

Before you begin

Please prepare:
(a) At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two
hard drives with identical model and capacity). If you do not want to create RAID, you may prepare
only one hard drive.
(b) An empty formatted floppy disk.
(c) Windows XP/2000 setup disk.
(d) Driver CD for your motherboard.

A. nVIDIA

® nForce 590SLI Southbridge
(1) Installing SATA hard drive(s) in your computer

Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port(s) on the motherboard. If there are more than one SATA controller on your motherboard, you
may refer to the motherboard user's manual to identify the SATA controller for the connector. Then
connect the power connector from your power supply to the hard drive.

4-1-4 Configuring SATA Hard Drive(s)

GA-M59SLI-S5/GA-M59SLI-S4 Motherboard - 80 -

English

Figure 1
Ensure that

NV SATA RAID function is enabled (Figure 2). For example, if you wish to create RAID
with hard disks on the SATAII0 and SATAII1 connectors, ensure that NV SATA 1 Primary/Secondary
RAID are enabled (Figure 2).
The BIOS Setup menus described in this section may not show the exact settings for your
motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard
you have and the BIOS version.
Figure 2

(2) Configuring SATA controller mode and boot sequence in BIOS Setup

You have to make sure whether the SATA controller is configured correctly in system BIOS Setup and
set BIOS boot sequence for the SATA hard drive(s)/RAID array.
Step 1:
Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). In BIOS
Setup, go to

Integrated Periperals --> Serial-ATA RAID Config (Figure 1).

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
Integrated Peripherals

��

Serial-ATA RAID Config [Press Enter]
On-Chip IDE Channel0 [Enabled]
On-Chip MAC Lan [Auto]
On-Chip MAC1 Lan [Auto]
NV Serial-ATA Controller [All Enabled]
IDE Prefetch Mode [Enabled]
Onboard Audio Function [Auto]

��

SMART LAN [Press Enter]
Onboard 1394 [Enabled]
Onboard LAN Boot ROM [Disabled]
Onboard SATA/IDE Ctrl Mode 1 [IDE]
Onboard Serial Port 1 [3F8/IRQ4]
Onboard Parallel Port [378/IRQ7]
Parallel Port Mode [SPP]

x ECP Mode Use DMA 3

On-Chip USB [V1.1+V2.0]
USB Keyboard Support [Disabled]
USB Mouse Support [Disabled]
Legacy USB Storage detect [Enabled]

��������

: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F11/12: Profile F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Item Help
Menu Level��

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
Serial-ATA RAID Config
Item Help
Menu Level

��

NV SATA RAID function [Enabled]

NV SATA 1 Primary RAID

[Enabled]

NV SATA 1 Secondary RAID

[Enabled]

NV SATA 2 Primary RAID

[Disabled]

NV SATA 2 Secondary RAID

[Disabled]

NV SATA 3 Primary RAID

[Disabled]

NV SATA 3 Secondary RAID

[Disabled]

��������

: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F11/12: Profile F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

- 81 - Appendix

English

Step 2:
To boot from Windows installation CD-ROM, set

First Boot Device under the Advanced BIOS
Features menu to CDROM (Figure 3).
Step 3:

Save and exit BIOS Setup.

Jel to?

P.S. a+Ako je to molio bi nekog da mi prevede na Hrvastki ...