PC Ekspert Forum - View Single Post

NemoRS · 31.10.2009., 20:55

Nisam zapeo ali me silno zanima.Uostalom tih 2000 sam platio i zelio sam da radi na toliko.To se ispostavilo kao vrlo tezak clock i ono sto jesam uspio jest da radi na 1950Mhz.Poslao sam upit i u G skill i sad cu vam ovdje postat njihove postavke za moju konfiguraciju.Naravno da je puklo u roku vrlo brzo s primeom.Ali morao sam probati.Jos jedna stvar jest kad enable-am xmp profil na ramu da dobijem tih 2000Mhz ali onda procesor nemogu dignuti

(

Jos jedna stvar jest da sam probao i da zaokruzim proc na ravno 4Ghz i memoriju na 2000Mhz i to sa postvkama vrlo visokim cpu Vcore 1,43 i qpi 1.555 i kad je s primeom puklo na tim vrijednostima odustao sam jer mi je i sam G skill rekao da za to trebaju visoke vrijednosti qpi.

Dear Customer

This motherboard and processor combination may not be able to run DDR3-2000 with a 4.0GHz CPU frequency. A high QPI voltage is necessary in order to do so.

Try the following settings:

In MIT (MB Intelligent Tweaker):

CPU Clock Ratio - 18x for 3.6GHz
QPI Link Speed - AUTO
Base Clock Control - Enabled
BCLK Frequency - 200
Performance Enhance - Standard
Extreme Memory Profile - Disabled
System Memory Multiplier - 10

Uncore & QPI Features
Uncore Frequency - 4000

DRAM Timing Selectable - Manual

CAS Latency Time - 9
tRCD - 9
tRP - 9
tRAS - 24

Enter these for the other three as well.

Channel A Timing Settings

Advanced Timings
Command Rate - 2

Advanced Voltage Control
Load-Line Calibration - Disabled
CPU Vcore - 1.32V
QPI/VTT Voltage - 1.50V
CPU PLL - 1.900V

PCIE - AUTO
QPI PLL - 1.300V
IOH Core - 1.400V
ICH I/O - 1.600V
ICH Core - 1.300V
DRAM Voltage - 1.640V
Rest to AUTO

Let me know how that goes. You will need to fine tune according to what your motherboard wants for voltages and settings.

Thank you
GSKILL SUPPORT- Show quoted text -

Quoting Nemanja Kojic <nemo.renaultsport@gmail.com>:

Hello.I am from Croatia.

My nickname is nkojic on http://www.xtremesystems.org/forums

I need some help on my MBO GIGABYTE EX58-EXTREME and G.Skill Trident 6GB
PC3-16000 CL9 DDR3 and i7 920.

CPU CLOCK 20x
qpi link speed 7,02
uncore frequency 3900
BCLK 195
SPD 10x
Memory frequency 1950Mhz 8-9-8-24

cpuV core 1,3750V
qpi vtt 1,495V
ioh core 1,100V
Dram voltage 1,66V
Cpu PLL 1,840V

I need to set my cpu to 4Ghz and 2000Mhz ram.I need your help with voltage
to be stable.And how much of everything i can do to be stable and not to
burn something.Or some link how to set in bios but it must be my ram and my
motheboard.

Thanks!

Thank you
GSKILL SUPPORT

31.10.2009., 20:55	#371
NemoRS Premium Moj komp Datum registracije: Feb 2007 Lokacija: Osijek Postovi: 518	Nisam zapeo ali me silno zanima.Uostalom tih 2000 sam platio i zelio sam da radi na toliko.To se ispostavilo kao vrlo tezak clock i ono sto jesam uspio jest da radi na 1950Mhz.Poslao sam upit i u G skill i sad cu vam ovdje postat njihove postavke za moju konfiguraciju.Naravno da je puklo u roku vrlo brzo s primeom.Ali morao sam probati.Jos jedna stvar jest kad enable-am xmp profil na ramu da dobijem tih 2000Mhz ali onda procesor nemogu dignuti( Jos jedna stvar jest da sam probao i da zaokruzim proc na ravno 4Ghz i memoriju na 2000Mhz i to sa postvkama vrlo visokim cpu Vcore 1,43 i qpi 1.555 i kad je s primeom puklo na tim vrijednostima odustao sam jer mi je i sam G skill rekao da za to trebaju visoke vrijednosti qpi. Dear Customer This motherboard and processor combination may not be able to run DDR3-2000 with a 4.0GHz CPU frequency. A high QPI voltage is necessary in order to do so. Try the following settings: In MIT (MB Intelligent Tweaker): CPU Clock Ratio - 18x for 3.6GHz QPI Link Speed - AUTO Base Clock Control - Enabled BCLK Frequency - 200 Performance Enhance - Standard Extreme Memory Profile - Disabled System Memory Multiplier - 10 Uncore & QPI Features Uncore Frequency - 4000 DRAM Timing Selectable - Manual CAS Latency Time - 9 tRCD - 9 tRP - 9 tRAS - 24 Enter these for the other three as well. Channel A Timing Settings Advanced Timings Command Rate - 2 Advanced Voltage Control Load-Line Calibration - Disabled CPU Vcore - 1.32V QPI/VTT Voltage - 1.50V CPU PLL - 1.900V PCIE - AUTO QPI PLL - 1.300V IOH Core - 1.400V ICH I/O - 1.600V ICH Core - 1.300V DRAM Voltage - 1.640V Rest to AUTO Let me know how that goes. You will need to fine tune according to what your motherboard wants for voltages and settings. Thank you GSKILL SUPPORT- Show quoted text - Quoting Nemanja Kojic <nemo.renaultsport@gmail.com>: Hello.I am from Croatia. My nickname is nkojic on http://www.xtremesystems.org/forums I need some help on my MBO GIGABYTE EX58-EXTREME and G.Skill Trident 6GB PC3-16000 CL9 DDR3 and i7 920. CPU CLOCK 20x qpi link speed 7,02 uncore frequency 3900 BCLK 195 SPD 10x Memory frequency 1950Mhz 8-9-8-24 cpuV core 1,3750V qpi vtt 1,495V ioh core 1,100V Dram voltage 1,66V Cpu PLL 1,840V I need to set my cpu to 4Ghz and 2000Mhz ram.I need your help with voltage to be stable.And how much of everything i can do to be stable and not to burn something.Or some link how to set in bios but it must be my ram and my motheboard. Thanks! Thank you GSKILL SUPPORT