EVGA Classified SR-2 Info Thread

[bluefluid]

No, da li je itko vidio ovo cudo???



'A day or two ago we already reported that eVGA is working on a dual-socket (LGA 1366) motherboard. A new photo appeared.

This will be an uber high-end tweakers dual LGA-1366 motherboard based on the Intel 5500 "Tylersburg" chipset with the usual ICH10R Southbridge.

Considering you'll need SMP support the dual-socket motherboard will have to support the Xeon 5500 series. Probably, a future high-end Intel Core family CPU is released that is capable of dual-socket setups, too. The picture reveals two LGA-1366 sockets, each powered by an 8-phase digital PWM circuit. Each socket is wired to six DDR3 DIMM slots supporting triple-channel memory for that socket.

The board has 7 PCIe slots and to feed them the motherboard is equipped with two NF200 (NVIDIA) bridge chips to add additional PCIe lanes. It is now rumoured that this amazing board will also have an amazing price tag .. over 500 EUR.'

Izvor:guru3d

'The recently surfaced high-end dual socket LGA-1366 motherboard is pictured in full, without its cooling assembly. The picture reveals quite a bit about EVGA's new monstrosity. To begin with, the motherboard is neither ATX, nor EATX in the truest sense. Like the recently announced X58 Classified 4-way SLI which was based on the "XL-ATX" form-factor, this motherboard seems to be 13.58 inches (344.93 mm) long, and about as wide as EATX (330 mm, 13 inches), or maybe a little more.

Each LGA-1366 socket is wired to six DDR3 DIMM slots for triple-channel memory, and is powered by an 8-phase digital-PWM circuit. Each socket further has a 3-phase power circuit for its DIMM slots. The CPU VRM for each socket takes input from an 8-pin ATX, and what appears to be a 6-pin +12V (PCI-E?) connector. The motherboard further takes power from a 6-pin PCI-E power connector apart from the usual 24-pin ATX power connector. Some of these inputs may be redundant and needed only for additional electrical stability to support competitive overclocking.'

Izvor:techpowerup

[Baja 001]

To je ploča za render ekipu i par 3D Čmark jusera

Koliko RAMa? 24GB

[sinisa1989]

To ću si kupit.....za 5 godina
Divota od "pločice" nema daljnjeg.

Prebrutalno. Toliko snage na jednoj ploči. Ekipa kaj renderira će plakati od sreće. Da ne pričam mogućnosti od strane GPGPU-ova.

[hammer_of_thor]

Bolesno, 12 DIMM utora, 7 hebenih PCI-E slotova, baš me zanima koliko će staza imati
Ovo je farma u jednom

[ivand123]

Cijela ta platforma je blesavo moćna i ukoliko se ne koristi u profi svrhe krajnje nepotrebna plus cijena od oko 500 eura, pa to je skoro više od moje cijele konfe.

[sinisa1989]

Mislim da tih 500+ eura nije puno u odnosu na njezine karakteristike.

[Majo]

Drito to,prepolovis ju na 250E i opet imas sick plocu,mada imas samo pola ploce .

[hobitxxx]

Mene zanima kolko ce to WATA trebati kad bude puno OC-anih komponenata zapiknuto unutra.....2KW?

[bluefluid]

ma to je za amere, a kod njih ionak samo papci kupuju napajanja ispod kilovat i pol

ploca je savrsen pocetak za pilu iz snova: dva 975, 4x5870cfx, rama koliko ide i to sve pod vodom...

[Majo]

Pocetak?Sto li je kraj te pile onda ?

[sinisa1989]

Autor bluefluid

ma to je za amere, a kod njih ionak samo papci kupuju napajanja ispod kilovat i pol

ploca je savrsen pocetak za pilu iz snova: dva 975, 4x5870cfx, rama koliko ide i to sve pod vodom...

To da..ali ima jedan mali problem. Cijena.
@ Majo
6 x 30" monitora sa ultratankim rubom

[Jerry]

Ploca zahtijeva 1500W (24+8+8+6+6) ima dva NF200 chipa te je VECA od EATX standarda (vjerujem da NITKO od vas ne moze naci takav PSU a ne stane ni u koje SERVERSKO SSI EATX kuciste!).
Sve u svemu - promasaj (u odnosu na prethodni Skulltrail koji se takodjer nije proslavio)!