Fiberland, T-Com Optika (Ultra MAX)

[jp_rv]

hah, ne uspijevam nać tu očitu opciju :P
spojen sam preko serijskog unutra, listam config fajlove ali jedino mjesto gdje se spominje gpon serijski- ubacio sam drugi serijski ali svejedno se neće spojit na optiku, i na screenshotu gore je i dalje vidljiv originalni raisecom serijski a ne onaj kojega sam ubacio u config fajl.

[Blagus]

Nisam imao mira pa sam išao isprobati. Jesu ga Kinezi opravili, svaka im čast

1. Spojiš serial
2. Upališ ONT
3. Pritisneš enter kad ti veli da prekineš boot
4. Moraš promijeniti i serial i password, inače neće registrirati promjenu:
   

   setenv GPONSN XXXXXXXX
   setenv GPONPW xxxxxxxx

5. Spremiš promjene:
   

   saveenv

6. Resetiraš ga:
   

   reset

Opservacije:

• ako se promijeni samo serial u U-Bootu, web UI to neće registrirati. Ako se u tom stanju kroz web promijeni password, ONT će poludjeti i neće se pokrenuti (nikad ne oživi na mreži niti pokrene optiku) ili će se pokrenuti ali s praznim serialom na webu. Iz tog stanja se izvuče tako da se promijene i serial i password u bootloaderu.
• Nakon što jednom registrira novi serial, PLOAM password se može bez problema mijenjati kroz web UI

[jp_rv]

1 [ERR] Warning, unknown dir name: FIBER_MODE ::::32 ... ::::1 ... CMD: /bin/route add default dev lo metric 10000 xml_mib_update():... ================ close wdt before download config=========== ================check software version====================== CMD: /bin/ifconfig eth0 hw ether 000e5e8c79fc CMD: /bin/brctl addbr br0 nor flash found! mount fs1 active img = 0 sw0 : 3.2.16_20160606 sw1 : 3.2.16_20160606 sw_version 0 : 3.2.16_20160606 sw1(backup) version: sw version0 : 3.2.16_20160606 sdevice eth0 entered promiscuous mode w_version1 : CMD: /bin/ifconfig br0 hw ether 000e5e8c79fc CMD: /bin/brctl stp br0 off 3.2.16_20160606 ====================check software version finish============== ------ [-u cs]Update cs setting ------ CMD: /bin/brctl setfd br0 1 CMD: /bin/brctl setageing br0 7200 CMD: /bin/brctl addif br0 eth0 sh: can't create /proc/sys/net/ipv6/conf/br0/dad_transmits: nonexistent directory CMD: /bin/ifconfig br0 192.168.1.1 netmask 255.255.255.0 mtu 1500 CMDre8670_open 3088 : /bin/boa CMD: /bin/ifconfig eth0 up br0: port 1(eth0) entering learning state drivers/net/rtl86900/sdk/src/rtk/pon_led.c:781 led sw blink init complete! rtk_pon_led_SpecType_set 0 sh: can't create /proc/sys/net/ipv6/********************los force blink conf/br0/dad_transmits: nonexistent directory sh: can't create /proc/br_igmpsnoop: nonexistent directory IGMP Snooping: enabled CMD: /bin/iptables -t mangle -D PREROUTING -i br0 -j lan_mark 1 0 1 br0: port 1(eth0) entering forwarding state 0 0 priority: 7, portmask 2, rx: 801e4ae0 insert here, priority: 7, portmask 255, rx: c00ef3b4 omci_app igmpd configd running GPON mode ... ----- do_rc [/etc/init.d/rc34] ----- Original [e] is missing!! Switch to new default [en]. iptables v1.2.7a: Couldn't find target `lan_mark' Try `iptables -h' or 'iptables --help' for more information. CMD: /bin/iptables -t mangle -N lan_mark CMD: /bin/iptables -t mangle -F lan_mark CMD: /bin/iptables -t mangle -A PREROUTING -i br0 -j lan_mark CMD: /bin/ebtables -D FORWARD -j portmapping ----- do_rc [/etc/init.d/rc35] ----- loopDetectInit 85 eth port num = 1 ELANVIF = eth0 req.ifr_name[0]=[eth0] eth0 ifindex=2 mac= 00:02:00:00:00:00 starting pid 465, tty '/dev/ttyS0': '/bin/login -p' login: size of linux : 1441792 size of linux : 3932160 init_global_parm834::size of g_max_upload_size : 3932160 Illegal target name 'portmapping'. CMD: /bin/ebtables -N portmapping CMD: /bin/ebtables -A FORWARD -j portmapping Port Loop Detect App is running. loopDetectFd=3 CMD: /bin/ip rule del fwmark 0x1000000/0xff000080 [xml_INFO]: Update cs configuration success. RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0x2000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0x3000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0x4000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0x5000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0x6000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0x7000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0x8000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0x9000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0xa000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0xb000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0xc000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0xd000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del fwmark 0xe000000/0xff000080 RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit igmpd is running: sys_max_port_num =3 ..... RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit listening RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule del prohibit RTNETLINK answers: No such file or directory CMD: /bin/ebtables -A portmapping -i eth+ -o eth+ -j RETURN CMD: /bin/ebtables -A portmapping -i eth+ -o wlan+ -j RETURN CMD: /bin/ebtables -A portmapping -i wlan+ -o eth+ -j RETURN CMD: /bin/ebtables -A portmapping -i wlan+ -o wlan+ -j RETURN CMD: /bin/ebtables -A portmapping -i eth0+ -j DROP CMD: /bin/ebtables -A portmapping -i wlan+ -j DROP CMD: /bin/ebtables -I portmapping 1 -i eth0.2 -o nas0_0 -j RETURN CMD: /bin/ebtables -I portmapping 1 -i nas0_0 -o eth0.2 -j RETURN CMD: /bin/ebtables -A portmapping -i nas0_0 -j DROP gpon_password_len = 8 Module libigmpipc.so is loaded and inited priority: 7, portmask 255, rx: c00ef3b4 priority: 7, portmask 2, rx: 801e4ae0 priority: 6, portmask 2, rx: 801e65c4 priority: 0, portmask 127, rx: 802ad99c pinsert here, priority: 4, portmask 2, rx: 801d7acc ptp_eth_uni_set_max_frame_size 329 port: 0 mtu = 2031 ver = 3.2.16_20160606 ver1 = 3, ver2 = 2 ver3 = 16 date = 20160606 ver = 3.2.16_20160606 ver1 = 3, ver2 = 2 ver3 = 16 date = 20160606 inet addr: 192.168.1.1 lan ip br0 192.168.1.1 192 168 1 1 c0a8 101 omci_wrapper_msgHandler: devMode 0,receiveState 1,logLevel 0,sn RCMG0/W Password: login: telecomadmin Password: BusyBox v1.12.4 (2016-06-06 13:01:45 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. #

[Blagus]

Tvoj je totalna suprotnost mojem - kod mog je vidljiv bootloader a kernel je tih, kod tebe samo kernel ispisuje poruke i imaš Linux shell. Ajde provjeri jel imaš fw_printenv i fw_setenv naredbe pa s njima prouči koje varijable imaš.

[skalar]

Autor c-shadow

Mene više brine što će biti kad/ako nam HT uvali ove nove all-in-one uređaje gdje je ONT integriran skupa s routerom.
Koji hw sad daju ako se zatraži Gb brzina?

za gb brzine sigurno neće razlog je za tehnicolora nepostoji mash uređaj,a premium router, znaći router + mash ,a tih 5kn više na računu su im itekako dragi.

[tascam]

Ja ima Tehnicolora i radi savršeno.Na njega je zakačen 7590 kao AP

[gothfr34k]

Autor gothfr34k

Quote s druge teme:



"Ajde super, presretan sam Baš je danas netko od tehičara/zaposlenika Tcoma zvonio ženi i tražio predstavnika stanara i onda vidim poruku na forumu Budem odahnuo napokon."



I sad, na oglasnoj stoji da stanari trebaju potpisati da se uvede optika u zgradu u Vinogradi ulica.

Ima jedno, možda lažem, 10tak stanova u zgradi.

Niti jednog potpisa....

Glavno kad otvorim wifi svi furaju "pokućni" internet, koji sam i ja probao, i koji je sranje, bar nakon 12-01 ujutro.

Za popizditi..

Koga upregnuti? Predstavnika stanara da traži potpise? Slična iskustva?

Eto stiže i kod mene optika napokon. poceli su prije god dana, moj dio ulice ostavili za zadnje Danas me iz iskona zovu da je dostupna optika, sad tu imam samo 20/2 jedva. Sad ćemo zvati Tcom pa optika na max. Moram vidjeti da li imaju kakve akcije za nove korisnike.

[spawn]

Autor tascam

Ja ima Tehnicolora i radi savršeno.Na njega je zakačen 7590 kao AP

Potvrđujem. Nisam ga još nijednom ugasio, brzine i pin stabilni full, nema padova. Za sada super zadovoljan

[beetle|juice]

Ja prijavio nedavno smetnju na optici, pa mi dosao tehnicar i uspio ga nagovorit da mi pukne Technicolora umjesto Speedporta. Radi super u router modu, no posto mi treba bridge mode da mi MK bude glavni router potrebno je samo maknut s Technicolora login podatke za PPP i ukljucit PPPoE Passthrough(po defaultu je ukljucen) i eto MK moze radit PPPoE konekciju koja radi savrseno. Ukoliko se preko Moj Telekom Portala promjeni nacin rada u bridge mode, onda ne radi bridge kako treba, tako da se ostavi na portalu da radi normalno u routing modu i sve ostalo sljaka.

[skalar]

jučer sam dobio Speedporta 3, prvi dojmovi niš posebno, ali bar za sada ni razočaravajuće,
kad skužiš gdje što stoji sve radi, sučelje mu nije standardno pa treba kopati čak mu je i upload firmwarea otvoren - što sam se stvarno začudio.
u razgovoru sa tehničarem je potvrdio da su prvi firmwarei za Technicolora su bili katastrofa
ali da su sada ok, pa otuda i moja loša iskustva.

[dadoremix]

A kak ti je izgled sucelja u speedportu?
Kod mene bez ikona, samo tekst
Cak sam isao sa ie na modem
Jer izgleda ko ds java fali ili adblocker blokira

Ajd pa 1 dan proveo u tom okruzenju, sad je sve na mikrotiku

[Nikky]

Dali adblocker zeza lako riješiš, privremeno ga ugasiš a može se definirati da ne filtrira sa 192.168.1.1/ adrese,
mada je to sve skupa bljak kad se oko takvih stvari treba zezati.

Kako to da GUI uredno radi kod recimo Asusa i ostalih ?

Ima ona stara od g... nemoš napravit pitu

[Mario92]

Uskoro se selim u hižu gdje imam HT-ovu optiku, i zovem ja njih da vidim kakva je procedura sklapanje ugovora na moje ime iako još kuća ne glasi na mene... Nisam znal, ali mogu već sad pokrenuti zahtjev za Internet i potpisati UO da glasi na mene iak sama nekretnina nije još na mene...