za vlasnike pixme 4000

[fanATIk]

ja kao i mnogi drugi vlasnici pixmi 4000(kao što sam vidio na forumu) smo živjeli u neznanju. uvriježeno mišljenje je bilo da printer kada printa na cd/dvd (u canonovom softwareu) nemre isprintat sliku skroz do rupe na disku nego ostavlja bijelim dio neposredno oko rupe. pogrešno! može printat skroz. kad uđete u cdlabelprint,
izaberite new, zatim select paper. onda na dnu kliknite na new i otvorit će se jedan prozor na kome podesite outer i inner size kako vas volja. isto vrijedi i za pixmu 4200.
oni koji su to znali nek mi se ne smiju. masa ljudi to nije znala.

[Isus]

isto vrijedi za pixmu 3000.

[alimilano]

..vjerujem da je većina to ipak znala...

[fanATIk]

Autor alimilano

..vjerujem da je većina to ipak znala...

pa di si bio kad se na forumu raspravljalo o tome i kad su svi preporučivali acousticu cd/dvd label maker mjesto canonovog softwarea?

[alimilano]

..ko će to znat ali da sam to vidio dobili bi ste odgovor....

[kony]

ja sam kupio pixmu prije 3 dana i nisam znao

hvala

[Zlatko62]

Ja molim ako netko zna odgovor da mi napiše. Printer IP4000 kada ga upalim blicne 5 puta žuto i jednom zeleno i tako skroz javlja nekakvu grešku ali ne kužim šta treba.

[Crash009]

Pun ti je waste apsorber.

Googlaj "waste apsorber ink reset"
Za ip1000 je fora da ga iskljucis iz struje pritisnes i drzis ON tipku i onda spojis nazad u utičnicu, i printer radi oke sve dok ga ne iskljucis iz struje, onda ga moras ponovo resetirati.

[fanATIk]

Vidi ovdje.
Edit: Našao popis šta znači blinkanje.

2-1. Operator Call Errors (by LED Blinking in Orange)

*1: Only for models supporting CD-R printing

*2: Only for models not supporting CD-R printing
LED blinking
in orange Error [Error code] Solution Remarks

2 times No paper. (ASF) [1000] Set the paper in the ASF, and press the Resume/Cancel
button.
No CD-R tray. [1001]*1 Set the CD-R tray, and press the Resume/Cancel button.
No paper in the cassette. [1003]
(No paper in the front paper feed cassette.)
Set the paper in the cassette, and press the Resume/Cancel
button.

3 times Paper jam. [1300] Remove the jammed paper, and press the Resume/Cancel
button.
Paper jam in the under guide. [1304]
Paper jam in the rear guide. [1303]
Front door closed. [1250] Open the paper output tray.

4 times No ink. [1601 / 1602 / 1611 / 1612 / 1613] Replace the empty ink tank(s), or press the Resume/Cancel
button.
Pressing the
Resume/Cancel button
will exit the error without
ink tank replacement,
however, ink may run out
during printing.

5 times The print head is not installed [1401], or it is not
properly installed (EEPROM data of the print
head is faulty) [1403 / 1405].
Install the print head properly, and close the access cover.
Or, with the print head installed, turn the printer off and on.

6 times Inner cover open. [1841]*2 Close the inner cover, and press the Resume/Cancel button.
Inner cover open (during printing on paper).
[1846]*2
Close the inner cover, and press the Resume/Cancel button.
CD-R tray guide closed (during CD-R printing).
[1850 / 1855]*1
Open the CD-R tray guide, set the CD-R tray properly, and
press the Resume/Cancel button.
CD-R tray guide open (during printing to paper).
[1851 / 1856]*1
Close the CD-R tray guide, and press the Resume/Cancel
button.

7 times*1 No CD-R or DVD-R. [1002] After setting a CD-R or DVD-R in the tray, set the tray in the
tray guide, and press the Resume/Cancel button.

8 times Warning: The waste ink absorber becomes
almost full (approx. 95% of the maximum
capacity). [1700]
Pressing the Resume/Cancel button will exit the error, and
enable printing.
In repair servicing, replace the bottom case unit (QM2-1205),
or the ink absorbers (QC1-4222 / 4223 / 4224 / 4263 / 4264 /
4864 / 4221 / 4257).
The service call error,
indicating the waste ink
absorber is full, is likely to
occur soon.

9 times The connected digital camera or digital video
camera does not support Camera Direct Printing.
[2001]
After removing the cable between the camera and the printer,
press the Resume/Cancel button, and re-connect the cable.

10 times Automatic duplex printing cannot be performed
(paper size not supported). [1310]
Press the Resume/Cancel button to eject the paper being used
at error occurrence. Printing will resume from on the front
side of the next page.
Data which was to be
printed on the back side of
paper at error occurrence is
skipped (not printed).

11 times Failed in automatic print head alignment. [2500] Press the Resume/Cancel button, and after confirming the
following, perform print head alignment again:
- Set an appropriate type and size of paper (plain paper, A4 or
letter).
- Check that the nozzle check pattern is properly printed (all
ink ejected, no faint printing).
- Protect the paper output slot from exposure to excessive
light.
Access cover open. [1200] Close the access cover.

Sve mi se čini da imaš problem s glavom za printanje. Možeš ju probat izvadit i očistit u alkoholu ali nema garancije da će ti uspjet.
Imao svojevremeno pixmu 4000 i imao isti problem. Glavu nisam uspio očistit, kupio novu pixmu, ne isplati se samo glavu kupovat.

[Vjeko]

Da se ubacim sa laganim OT, ima li tko glavu za pixmu 4000? Moja izdahnula bjeli dim

[fanATIk]

Ne isplati se kupovat. Kad je meni riknula, zvao canon i rekli 600 kn glava. Otišao u dućan i uzeo novi printer za 700 kn.

[Corporal Clegg]

Mali offtopic.
Zna li itko kako rijesiti onaj problem senzora koji odredjuje je li tray spusten? Naime, cesto mi se dogodi da je tray uredno spusten, a printer javlja da je podignut i ne moze printati :-k
Citao sam na nekim forumima kako se taj senzor moze nekako ubiti, ali nigdje nisam nasao kako, pa ako netko zna...
Vjerujem da nisam jedini s tim problemom.