Gigabyte EP45/43-DS3x/DS4/DS5/DQ6/Extreme Thread

[Razer]

Ili ploča ili memorija, nema što drugo biti. A ako je memorija išla na drugoj ploči, i ako si ju izolirao s najnižim djeliteljem na ovoj ploči, rješenje je očito.

[electro]

ram nije pošto sam probao sa jednim keksom 1gb 667 randitiona ,ista stvar
neznam zašto bi bila mb ako radi najnormalnije te se diže iz win sa easy tune-om 6?

[net]

Koje su postavke u biosu? Nikako nemoj ostavit cpu termination i cpu pll na auto, rucno stavi vrijednost (pri oc ako je na auto ploca daje enormno visoki napon). Probaj stavit ram na 1.9, mch core na 1.16, cpu pll, termination i vcore na normalne vrijednosti. Rucno unesi vrijednosti letacija memorije 5-5-5-18, subletacije 3-3-6-52-3-2 (Pisu s lijeve strane).

[electro]

probao ali ne pomaže
mb par (3-4)puta pokuša bootat a onda automatski postavi defaultni fsb i starta
nisam pametan,dali je zbilja mb sa felerom?
ponavljam da iz win sa easy tunerom 6 mogu dizat proc kakvih 25%

[E-mil]

ujebane su ti neke postavke u BIOSU

samo trebaš otkriti koje točno (ja glasam za memoriju)

probaj sve što se tiče RAM-a staviti na AUTO a ostalo (ovo što ti net savjetuje) postavi ručno

[net]

Problem je napamet bacat brojke koje si stavio u biosu. Ploca ima vdroop od 0.04 i vdrop od 0.04 na q6600, mozda procu dajes premalo struje ili je krivi strap itd... Koliko mislis ocat proc, koji je tocno model memorije (radni napon i letacije)?

[electro]

fora je da ne prihvača niti jedan fsb gore
kao da je zabetonirano,uporno javlja grešku pri boot-u zbog oc ili krivih posavki napona
http://img519.imageshack.us/img519/4090/slika0140.jpg

[Dizel]

Jesi probao uopce s drugim procesorom? Da ovaj nije slucajno bio kod maX-a i vesele ekipe s tekucim helijem...

[E-mil]

Standard

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 


Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: 
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go

Advanced Timing Control
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Channel B
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Motherboard Voltage Control

CPU
CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages

CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking

CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

MCH/ICH
MCH Core…………….....1.100V...........: << 
MCH Reference….…….0.760V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.500V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[Dizel]

Ma daj, ako ucita Load optimized defaults sve se vrati na tvornicke postavke...

[E-mil]

da, i to mu radi

onda pokrene windowse i kloka sa easytune, znači radi

kad ručno promijeni postavke u BIOSu, nešto sjebe i ne radi

[net]

Na slici vidim da si ostavio ram na turbo i na 900 mhz mozda je u tom poroblem. Ajd probaj s ovim postavkama za 333*9.0

B Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [AUTO]
CPU Clock Ratio ..........................: 9
CPU Frequency ...........................: 2997 333*9.0


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333
PCI Express Frequency (Mhz) .........: 100

DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 333

System Memory Multiplier ..............: 2.4B
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................18

CPU
CPU Vcore…. 1.225
CPU Termination…..... 1.200V
CPU PLL…………………....1.500V

MCH/ICH
MCH Core…………….....1.16V

DRAM
DRAM Voltage ……....1.9

CPU Enhanced Halt (C1E)................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]

Vcore mozes staviti vrijednost koja je bila stabilna pri ocanju iz windowsima. Ispuni template, nebi bilo na odmet znati koji se stock napon proca i memorije.

[electro]

mislim da mogu napraviti rezume
svi koji su smatrali da je problem u ram-u bili su točni (mislim 99%)
izgleda da 2x2gb A data 800MHz nije raspoloženo za clockanje na ovoj mb
(premda sam pokušao staviti samo 1gb 667 randition bez rezultata)
stavio 2x1 gb 667 ballistix digo napon na 2 V te malo dodao procu (1,2V)
uspio za sada iči na 320fsp (prije uopče nije bilo moguče maknuti se od 266fsb-default)
izgleda da je mb osjetljiva na napon
probat ču još malo testirat
hvala svima na trudu

[net]

Na koliko su radili balistixi pri tom oc, koji je bio multi memorije 2, ili 2.4, te na koliko je ploca radila (mch 266 ili 333)? Ispuni template za postavke koje si koristio sa basitixima. Napisi slobodno koja je tocno memorija od a-date i tvornicki napon i letacije.