|
White Rabbit
Datum registracije: May 2006
Lokacija: -
Postovi: 5,062
|
Citiraj:
Autor c-shadow
A što ti pokazuje router kad se spojiš s tim intel adapterom?
Kako vidi klijenta, na kojem bandu, širini, rx/tx,...?
Na strani linux klijenta isto možeš to sve lijepo pogledati  |
Hm...router ili nije pricljiv ili sam ja preglup (ne iskljucujem , mreze mi nisu jaca strana) naci ikakav smisleni info na tom cudu....hovewer evo sa Linux strane:
Code:
bash-5.2# iw wlp41s0 info
Interface wlp41s0
ifindex 3
wdev 0x1
addr 0a:95:ab:85:88:8e
type managed
wiphy 0
channel 40 (5200 MHz), width: 80 MHz, center1: 5210 MHz
txpower 22.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
bash-5.2# iw dev wlp41s0 link
Connected to 60:32:b1:67:58:ab (on wlp41s0)
SSID: Toansi
freq: 5200.0
RX: 6643869 bytes (6259 packets)
TX: 514610 bytes (1962 packets)
signal: -59 dBm
rx bitrate: 6.0 MBit/s
tx bitrate: 234.0 MBit/s VHT-MCS 3 80MHz VHT-NSS 2
bss flags: short-slot-time
dtim period: 1
beacon int: 100
Jos debugging infa ako zatreba:
Code:
bash-5.2# iw list
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 20
max scan IEs length: 413 bytes
max # sched scan SSIDs: 20
max # match sets: 8
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
* CMAC (00-0f-ac:6)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* P2P-client
* P2P-GO
* P2P-device
Band 1:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT Max RX data rate: 300 Mbps
HT TX/RX MCS rate indexes supported: 0-15
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412.0 MHz [1] (22.0 dBm)
* 2417.0 MHz [2] (22.0 dBm)
* 2422.0 MHz [3] (22.0 dBm)
* 2427.0 MHz [4] (22.0 dBm)
* 2432.0 MHz [5] (22.0 dBm)
* 2437.0 MHz [6] (22.0 dBm)
* 2442.0 MHz [7] (22.0 dBm)
* 2447.0 MHz [8] (22.0 dBm)
* 2452.0 MHz [9] (22.0 dBm)
* 2457.0 MHz [10] (22.0 dBm)
* 2462.0 MHz [11] (22.0 dBm)
* 2467.0 MHz [12] (22.0 dBm)
* 2472.0 MHz [13] (22.0 dBm)
* 2484.0 MHz [14] (disabled)
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT Max RX data rate: 300 Mbps
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x039071f6):
Max MPDU length: 11454
Supported Channel Width: 160 MHz
RX LDPC
short GI (80 MHz)
short GI (160/80+80 MHz)
TX STBC
SU Beamformee
MU Beamformee
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT extended NSS: supported
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180.0 MHz [36] (22.0 dBm) (no IR)
* 5200.0 MHz [40] (22.0 dBm) (no IR)
* 5220.0 MHz [44] (22.0 dBm) (no IR)
* 5240.0 MHz [48] (22.0 dBm) (no IR)
* 5260.0 MHz [52] (22.0 dBm) (no IR, radar detection)
* 5280.0 MHz [56] (22.0 dBm) (no IR, radar detection)
* 5300.0 MHz [60] (22.0 dBm) (no IR, radar detection)
* 5320.0 MHz [64] (22.0 dBm) (no IR, radar detection)
* 5340.0 MHz [68] (disabled)
* 5360.0 MHz [72] (disabled)
* 5380.0 MHz [76] (disabled)
* 5400.0 MHz [80] (disabled)
* 5420.0 MHz [84] (disabled)
* 5440.0 MHz [88] (disabled)
* 5460.0 MHz [92] (disabled)
* 5480.0 MHz [96] (disabled)
* 5500.0 MHz [100] (22.0 dBm) (no IR, radar detection)
* 5520.0 MHz [104] (22.0 dBm) (no IR, radar detection)
* 5540.0 MHz [108] (22.0 dBm) (no IR, radar detection)
* 5560.0 MHz [112] (22.0 dBm) (no IR, radar detection)
* 5580.0 MHz [116] (22.0 dBm) (no IR, radar detection)
* 5600.0 MHz [120] (22.0 dBm) (no IR, radar detection)
* 5620.0 MHz [124] (22.0 dBm) (no IR, radar detection)
* 5640.0 MHz [128] (22.0 dBm) (no IR, radar detection)
* 5660.0 MHz [132] (22.0 dBm) (no IR, radar detection)
* 5680.0 MHz [136] (22.0 dBm) (no IR, radar detection)
* 5700.0 MHz [140] (22.0 dBm) (no IR, radar detection)
* 5720.0 MHz [144] (22.0 dBm) (no IR, radar detection)
* 5745.0 MHz [149] (22.0 dBm)
* 5765.0 MHz [153] (22.0 dBm)
* 5785.0 MHz [157] (22.0 dBm)
* 5805.0 MHz [161] (22.0 dBm)
* 5825.0 MHz [165] (22.0 dBm)
* 5845.0 MHz [169] (disabled)
* 5865.0 MHz [173] (disabled)
* 5885.0 MHz [177] (disabled)
* 5905.0 MHz [181] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* tdls_mgmt
* tdls_oper
* start_sched_scan
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* channel_switch
* set_qos_map
* add_tx_ts
* set_multicast_to_unicast
* Unknown command (156)
WoWLAN support:
* wake up on disconnect
* wake up on magic packet
* wake up on pattern match, up to 20 patterns of 16-128 bytes,
maximum packet offset 0 bytes
* can do GTK rekeying
* wake up on GTK rekey failure
* wake up on EAP identity request
* wake up on 4-way handshake
* wake up on rfkill release
* wake up on network detection, up to 8 match sets
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 1, #{ P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
total <= 3, #channels <= 2
* #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
total <= 3, #channels <= 1
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports per-vif TX power setting
P2P GO supports CT window setting
P2P GO supports opportunistic powersave setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device adds DS IE to probe requests
Device can update TPC Report IE
Device supports static SMPS
Device supports dynamic SMPS
Device supports WMM-AC admission (TSPECs)
Device supports configuring vdev MAC-addr on create.
Device supports randomizing MAC-addr in scans.
Device supports randomizing MAC-addr in sched scans.
Device supports randomizing MAC-addr in net-detect scans.
max # scan plans: 2
max scan plan interval: 65535
max scan plan iterations: 254
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xb0 0xd0
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ MU_MIMO_AIR_SNIFFER ]: MU-MIMO sniffer
* [ SCAN_START_TIME ]: scan start timestamp
* [ BSS_PARENT_TSF ]: BSS last beacon/probe TSF
* [ BEACON_RATE_LEGACY ]: legacy beacon rate setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ FILS_MAX_CHANNEL_TIME ]: FILS max channel attribute override with dwell time
* [ ACCEPT_BCAST_PROBE_RESP ]: accepts broadcast probe response
* [ OCE_PROBE_REQ_HIGH_TX_RATE ]: probe request TX at high rate (at least 5.5Mbps)
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ ENABLE_FTM_RESPONDER ]: enable FTM (Fine Time Measurement) responder
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ PROTECTED_TWT ]: protected Target Wake Time (TWT) support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
* [ PROT_RANGE_NEGO_AND_MEASURE ]: support for MFP in range measurement negotiation/procedure
* [ POWERED_ADDR_CHANGE ]: can change MAC address while up
* [ SPP_AMSDU_SUPPORT ]: SPP A-MSDU support
Peer measurement (PMSR)
Max peers: 5
REPORT_AP_TSF
RANDOMIZE_MAC_ADDR
FTM (Fine time measurement or Flight time measurement)
Preambles: LEGACY HT VHT
Bandwidth: 20_NOHT 20 40 80 160
ASAP
NON_ASAP
REQ_LCI
REQ_CIVICLOC
TRIGGER_BASED
NON_TRIGGER_BASED
bash-5.2$ iw reg get
global
country DE: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 20), (N/A)
(5150 - 5250 @ 80), (N/A, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5725 @ 160), (N/A, 26), (0 ms), DFS
(5725 - 5875 @ 80), (N/A, 13), (N/A)
(5945 - 6425 @ 320), (N/A, 23), (N/A), NO-OUTDOOR
(57000 - 66000 @ 2160), (N/A, 40), (N/A)
phy#0 (self-managed)
country DE: DFS-UNSET
(2402 - 2437 @ 40), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS, NO-80MHZ, NO-160MHZ
(2422 - 2462 @ 40), (6, 22), (N/A), AUTO-BW, NO-80MHZ, NO-160MHZ
(2447 - 2482 @ 40), (6, 22), (N/A), AUTO-BW, NO-HT40PLUS, NO-80MHZ, NO-160MHZ
(5170 - 5190 @ 160), (6, 22), (N/A), NO-OUTDOOR, AUTO-BW, IR-CONCURRENT, NO-HT40MINUS, NO-320MHZ, PASSIVE-SCAN
(5190 - 5210 @ 160), (6, 22), (N/A), NO-OUTDOOR, AUTO-BW, IR-CONCURRENT, NO-HT40PLUS, NO-320MHZ, PASSIVE-SCAN
(5210 - 5230 @ 160), (6, 22), (N/A), NO-OUTDOOR, AUTO-BW, IR-CONCURRENT, NO-HT40MINUS, NO-320MHZ, PASSIVE-SCAN
(5230 - 5250 @ 160), (6, 22), (N/A), NO-OUTDOOR, AUTO-BW, IR-CONCURRENT, NO-HT40PLUS, NO-320MHZ, PASSIVE-SCAN
(5250 - 5270 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-320MHZ, PASSIVE-SCAN
(5270 - 5290 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-320MHZ, PASSIVE-SCAN
(5290 - 5310 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-320MHZ, PASSIVE-SCAN
(5310 - 5330 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-320MHZ, PASSIVE-SCAN
(5490 - 5510 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-320MHZ, PASSIVE-SCAN
(5510 - 5530 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-320MHZ, PASSIVE-SCAN
(5530 - 5550 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-320MHZ, PASSIVE-SCAN
(5550 - 5570 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-320MHZ, PASSIVE-SCAN
(5570 - 5590 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-320MHZ, PASSIVE-SCAN
(5590 - 5610 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-320MHZ, PASSIVE-SCAN
(5610 - 5630 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-320MHZ, PASSIVE-SCAN
(5630 - 5650 @ 160), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-320MHZ, PASSIVE-SCAN
(5650 - 5670 @ 80), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-160MHZ, NO-320MHZ, PASSIVE-SCAN
(5670 - 5690 @ 80), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-160MHZ, NO-320MHZ, PASSIVE-SCAN
(5690 - 5710 @ 80), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40MINUS, NO-160MHZ, NO-320MHZ, PASSIVE-SCAN
(5710 - 5730 @ 80), (6, 22), (0 ms), DFS, AUTO-BW, NO-HT40PLUS, NO-160MHZ, NO-320MHZ, PASSIVE-SCAN
(5735 - 5755 @ 80), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS, NO-160MHZ, NO-320MHZ
(5755 - 5775 @ 80), (6, 22), (N/A), AUTO-BW, NO-HT40PLUS, NO-160MHZ, NO-320MHZ
(5775 - 5795 @ 80), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS, NO-160MHZ, NO-320MHZ
(5795 - 5815 @ 80), (6, 22), (N/A), AUTO-BW, NO-HT40PLUS, NO-160MHZ, NO-320MHZ
(5815 - 5835 @ 20), (6, 22), (N/A), AUTO-BW, NO-HT40MINUS, NO-HT40PLUS, NO-80MHZ, NO-160MHZ, NO-320MHZ
bash-5.2# iw dev wlp41s0 station dump
Station 60:32:b1:67:58:ab (on wlp41s0)
inactive time: 5707 ms
rx bytes: 25909
rx packets: 209
tx bytes: 12157
tx packets: 90
tx retries: 0
tx failed: 0
beacon loss: 0
beacon rx: 648
rx drop misc: 57
signal: -59 [-59] dBm
signal avg: -56 dBm
beacon signal avg: -59 dBm
tx bitrate: 234.0 MBit/s VHT-MCS 3 80MHz VHT-NSS 2
tx duration: 0 us
rx bitrate: 6.0 MBit/s
rx duration: 0 us
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 1
beacon interval:100
short slot time:yes
connected time: 71 seconds
associated at [boottime]: 59.720s
associated at: 1760883956548 ms
current time: 1760884026935 ms
|