Imam problem sa oc-om e7400, trenutno stabilno radi na 333 x 10,5 sto mu dodje 3,5 GHz ali cim pomaknem frekfenciju za 1 ili vise MHz kompu uopce nece bootati nego vrati postavke nakon par neuspjelih bootanja...
Više sam izludio pa molim za pomoc....
Konfa je u potpisu a evo i cpu-z validacije:
i setup biosa:
Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................: fast
CPU Clock Ratio .........................: 10x
Fine CPU Clock Ratio.....................: 0.5
CPU Frequency ...........................: 3.5Ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control...................: [Enabled]
CPU Host Frequency (Mhz) ................: 333Mhz
PCI Express Frequency (Mhz) .............: 100
C.I.A.2 .................................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive..........................: 800 mV
PCI Express Clock Drive..................: 900 mV
CPU Clock Skew (ps)......................: 0 ps
MCH Clock Skew (ps)......................: 0 ps
DRAM Performance Control
Performance Enhance......................: [STANDARD]
(G)MCH Frequency Latch...................: [auto]
System Memory Multiplier ................: 2.40B
Memory Frequency (Mhz) ..................: 800Mhz
DRAM Timing Selectable ..................: [Manual]
Standard Timing Control
CAS Latency Time.........................: 5
tRCD ....................................: 5
tRP'.....................................: 5
tRAS.....................................: 18
Advanced Timing Control
tRRD.....................................: auto
tWTR.....................................: auto
tWR......................................: auto
tRFC.....................................: auto
tRTP.....................................: auto
Command Rate (CMD) ......................: auto
Channel A
Static tRead Value.......................: auto
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment....................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)...................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)...................: Auto
Dimm1 Clock Skew Control.................: Auto
Dimm2 Clock Skew Control.................: Auto
DDR write Training...........................:auto
Channel B
Static tRead Value.......................: auto
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment....................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)...................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)...................: Auto
Dimm1 Clock Skew Control.................: Auto
Dimm2 Clock Skew Control.................: Auto
Motherboard Voltage Control
Voltage Type.............................: Manual
CPU
CPU Vcore................................: 1.35625V
CPU Termination..........................: Auto
CPU PLL..................................: Auto
CPU Reference............................: Auto
MCH/ICH
MCH Core.................................: Auto (normal shows as 1.100V)
MCH Reference............................: Auto (normal shows as 0.760V)
MCH/DRAM Ref.............................: Auto (normal shows as 0.900V)
ICH I/O..................................: auto (normal shows as 1.500V)
DRAM
DRAM Voltage.............................: 1.9
DRAM Termination.........................: auto
Channel A Reference......................: auto
Channel B Reference......................: auto
Advanced Settings
Limit CPUID Max. to 3....................: [Disabled]
No-Execute Memory Protect................: [Enabled]
CPU Enhanced Halt (C1E)..................: [Disabled]
C2/C2E State Support.....................: [Disabled]
x C4/C4E State Support...................: [Disabled]
CPU Thermal Monitor 2(TM2) ..............: [Enabled]
CPU EIST Function........................: [Disabled]
danke....