PC Ekspert Forum
Stranica 58 od 151 « Prva 84854555657 58 5960616268108 Zadnja »
Show 40 post(s) from this thread on one page

PC Ekspert Forum (https://forum.pcekspert.com/index.php)
-   Operativni sustavi (https://forum.pcekspert.com/forumdisplay.php?f=36)
-   -   Linux OS - info, how-to, pitanja, novosti, savjeti, problemi... (https://forum.pcekspert.com/showthread.php?t=234127)

chief_wolfinjo 21.07.2022. 06:03
Bok,

imam stariji iMac na koji je instaliran Ubuntu 20.04.

sve radi uredu, međutim povremeno korisničko sučelje

po pitanju grafike podivlja. jednostavno se sve pošemeri kao ovo:

https://i.ibb.co/8Pg3cyw/e4waeybm2vo51.jpg

pretpostavljam da je možda problem u driverima za gpu.

pa me zanima kako isprobati neke druge drivere ?

i koliko je ih uopće dostupno

hvala

tomek@vz 21.07.2022. 08:08
Citiraj:
Autor No123 (Post 3611555)
Već neko vrijeme imam instaliran OpenSuse Tumbleweed, sve radi OK samo nakon instaliranja svakog novog kernela moram ponovo instalirati driver za Wi-Fi DWA-172, a instalirao sam ga sa "sudo make dkms_install".

To mi se na Fedori nije dešavalo.

Ima li neko rješenje da ne moram stalno instalirati taj driver nego samo jednom?

Jer Fedora ima drukciji default slozeni, na OpenSuse moras vise toga rucno slagat. DKMS nije driver za WIFI nego aplikacija koja rekompajlira kernel modul (driver) za novi kernel. Sto se samo drivera tice - najcesce ne trebas driver instalirat nego samo firmware moras iscupat od nekud (jer je propriatery) i lupit u /lib/firmware. Lupi zypper in -y firmware* > reboot i pogledaj dmesg output jel sta javlja za wifi. Drugo pitanje je - dali DKMS uopce sljaka kak spada (imaj na umu i ovo sto je Nino napisao).


Citiraj:
Autor No123 (Post 3612784)
Imam USB 3.0 od 64GB Kingston Data Traveler 100 G3 i ne radi mi u USB 3.0 utoru, a radi u USB 2.0 utoru, a i USB 2.0 od 128GB radi u USB 3.0 utoru.

Može li se nekako namjestiti da USB 3.0 64GB proradi u USB 3.0 utoru?

Imam Fedoru 36 Xfce.

Jel ostali stickovi rade u USB3 slotu? Jel USB3 kernel modul loadan? Koji USB3 cip je u pitanju (lspci -v)?

Citiraj:
Autor chief_wolfinjo (Post 3612785)
Bok,

imam stariji iMac na koji je instaliran Ubuntu 20.04.

sve radi uredu, međutim povremeno korisničko sučelje

po pitanju grafike podivlja. jednostavno se sve pošemeri kao ovo:

pretpostavljam da je možda problem u driverima za gpu.

pa me zanima kako isprobati neke druge drivere ?

i koliko je ih uopće dostupno

hvala

Koji Imac? Koji GPU je unutra?




P.S.- ekipo - nhf al malo vise truda i malo vise osnovnih informacija bi se ocekivalo ako trazite pomoc. Nitko od nas nije baba Vanga i nema carobnu kuglu da izjave "nekaj ne dela" vam da smislen odgovor.

chief_wolfinjo 21.07.2022. 08:54
problem je vezan za ovaj iMac:

https://i.ibb.co/MsZ4MP3/Screenshot-1.jpg

No123 21.07.2022. 08:55
Citiraj:
Autor tomek@vz
Jel ostali stickovi rade u USB3 slotu? Jel USB3 kernel modul loadan? Koji USB3 cip je u pitanju (lspci -v)?
Nisam sad kod kuće. Sva 4 usb 2.0 sticka rade u usb 3.0 slotu samo jedan usb 3.0 stick ne radi, a to mi je jedini usb 3.o stick koji imam.

tomek@vz 21.07.2022. 10:04
Citiraj:
Autor chief_wolfinjo (Post 3612805)
problem je vezan za ovaj iMac:

Ponavljam:

Citiraj:
Autor tomek@vz (Post 3612798)
Koji Imac? Koji GPU je unutra?

Bootaj Linux > CLI >
lspci -v -s $(lspci | grep ' VGA ' | cut -d" " -f 1) > pejstaj tu output

chief_wolfinjo 21.07.2022. 10:30
ok. hvala budem to napravio. sad nisam blizu imaca.

No123 21.07.2022. 15:04
Citiraj:
lspci | grep "USB 3.0"
02:00.0 USB controller: Renesas Technology Corp. uPD720201 USB 3.0 Host Controller (rev 03)
i ne radi.

tomek@vz 21.07.2022. 17:01
Citiraj:
Autor No123 (Post 3612896)
i ne radi.

Imas kontroler koji sam prekleo 1000 puta. Iskreno - uzmi neki drugi PCI kontroler da nema taj cip na sebi (VIA ne radi probleme).


Alternativno mozes probat:


https://rephlex.de/blog/2021/10/15/l...1-great-again/


Za svaki slucaj daj jos dmesg |grep usb output ovdje.

No123 22.07.2022. 03:04
Citiraj:
Autor tomek@vz (Post 3612920)
Imas kontroler koji sam prekleo 1000 puta. Iskreno - uzmi neki drugi PCI kontroler da nema taj cip na sebi (VIA ne radi probleme).


Alternativno mozes probat:


https://rephlex.de/blog/2021/10/15/l...1-great-again/


Za svaki slucaj daj jos dmesg |grep usb output ovdje.
Citiraj:
dmesg |grep usb
[ 0.479587] usbcore: registered new interface driver usbfs
[ 0.479604] usbcore: registered new interface driver hub
[ 0.479614] usbcore: registered new device driver usb
[ 1.730730] pci 0000:00:1a.7: quirk_usb_early_handoff+0x0/0x6e0 took 1177141 usecs
[ 2.930725] pci 0000:00:1d.7: quirk_usb_early_handoff+0x0/0x6e0 took 1171403 usecs
[ 3.529637] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18
[ 3.529653] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.529656] usb usb1: Product: EHCI Host Controller
[ 3.529658] usb usb1: Manufacturer: Linux 5.18.11-200.fc36.x86_64 ehci_hcd
[ 3.529665] usb usb1: SerialNumber: 0000:00:1a.7
[ 3.540610] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18
[ 3.540616] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.540619] usb usb2: Product: EHCI Host Controller
[ 3.540622] usb usb2: Manufacturer: Linux 5.18.11-200.fc36.x86_64 ehci_hcd
[ 3.540625] usb usb2: SerialNumber: 0000:00:1d.7
[ 3.541356] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.18
[ 3.541360] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.541362] usb usb3: Product: UHCI Host Controller
[ 3.541364] usb usb3: Manufacturer: Linux 5.18.11-200.fc36.x86_64 uhci_hcd
[ 3.541366] usb usb3: SerialNumber: 0000:00:1a.0
[ 3.541930] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.18
[ 3.541933] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.541936] usb usb4: Product: UHCI Host Controller
[ 3.541938] usb usb4: Manufacturer: Linux 5.18.11-200.fc36.x86_64 uhci_hcd
[ 3.541940] usb usb4: SerialNumber: 0000:00:1a.1
[ 3.542459] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.18
[ 3.542462] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.542465] usb usb5: Product: UHCI Host Controller
[ 3.542467] usb usb5: Manufacturer: Linux 5.18.11-200.fc36.x86_64 uhci_hcd
[ 3.542469] usb usb5: SerialNumber: 0000:00:1a.2
[ 3.543000] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.18
[ 3.543004] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.543007] usb usb6: Product: UHCI Host Controller
[ 3.543009] usb usb6: Manufacturer: Linux 5.18.11-200.fc36.x86_64 uhci_hcd
[ 3.543011] usb usb6: SerialNumber: 0000:00:1d.0
[ 3.543559] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.18
[ 3.543563] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.543565] usb usb7: Product: UHCI Host Controller
[ 3.543567] usb usb7: Manufacturer: Linux 5.18.11-200.fc36.x86_64 uhci_hcd
[ 3.543569] usb usb7: SerialNumber: 0000:00:1d.1
[ 3.544084] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.18
[ 3.544088] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.544090] usb usb8: Product: UHCI Host Controller
[ 3.544092] usb usb8: Manufacturer: Linux 5.18.11-200.fc36.x86_64 uhci_hcd
[ 3.544094] usb usb8: SerialNumber: 0000:00:1d.2
[ 3.544478] xhci_hcd 0000:02:00.0: failed to load firmware renesas_usb_fw.mem, fallback to ROM
[ 3.553742] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.18
[ 3.553746] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.553749] usb usb9: Product: xHCI Host Controller
[ 3.553751] usb usb9: Manufacturer: Linux 5.18.11-200.fc36.x86_64 xhci-hcd
[ 3.553753] usb usb9: SerialNumber: 0000:02:00.0
[ 3.554172] usb usb10: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.554203] usb usb10: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.18
[ 3.554206] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.554209] usb usb10: Product: xHCI Host Controller
[ 3.554211] usb usb10: Manufacturer: Linux 5.18.11-200.fc36.x86_64 xhci-hcd
[ 3.554212] usb usb10: SerialNumber: 0000:02:00.0
[ 3.554693] usbcore: registered new interface driver usbserial_generic
[ 3.554700] usbserial: USB Serial support registered for generic
[ 3.559630] usbcore: registered new interface driver usbhid
[ 3.559632] usbhid: USB HID core driver
[ 3.766522] usb 1-2: new high-speed USB device number 2 using ehci-pci
[ 3.910508] usb 6-1: new low-speed USB device number 2 using uhci_hcd
[ 3.915647] usb 1-2: New USB device found, idVendor=058f, idProduct=6362, bcdDevice= 1.00
[ 3.915655] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.915659] usb 1-2: Product: Flash Card Reader/Writer
[ 3.915662] usb 1-2: Manufacturer: Generic
[ 3.915665] usb 1-2: SerialNumber: 058F63626479
[ 4.088860] usb 6-1: New USB device found, idVendor=0458, idProduct=0186, bcdDevice=24.58
[ 4.088872] usb 6-1: New USB device strings: Mfr=4, Product=40, SerialNumber=0
[ 4.088879] usb 6-1: Product: Wired Mouse
[ 4.088885] usb 6-1: Manufacturer: KYE SYSTEMS CORP.
[ 4.105452] input: KYE SYSTEMS CORP. Wired Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/0003:0458:0186.0001/input/input6
[ 4.105592] hid-generic 0003:0458:0186.0001: input,hidraw0: USB HID v1.11 Mouse [KYE SYSTEMS CORP. Wired Mouse] on usb-0000:00:1d.0-1/input0
[ 4.105654] usbhid 6-1:1.1: couldn't find an input interrupt endpoint
[ 4.748522] usb 6-2: new low-speed USB device number 3 using uhci_hcd
[ 4.925821] usb 6-2: New USB device found, idVendor=1c4f, idProduct=0002, bcdDevice= 1.10
[ 4.925834] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.925839] usb 6-2: Product: HCT Keyboard
[ 4.925844] usb 6-2: Manufacturer: SEM
[ 4.942477] input: SEM HCT Keyboard as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/0003:1C4F:0002.0002/input/input7
[ 4.994782] hid-generic 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Keyboard [SEM HCT Keyboard] on usb-0000:00:1d.0-2/input0
[ 5.010532] input: SEM HCT Keyboard Consumer Control as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/0003:1C4F:0002.0003/input/input8
[ 5.062694] input: SEM HCT Keyboard System Control as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/0003:1C4F:0002.0003/input/input9
[ 5.062788] hid-generic 0003:1C4F:0002.0003: input,hidraw2: USB HID v1.10 Device [SEM HCT Keyboard] on usb-0000:00:1d.0-2/input1
[ 5.462522] usb 7-2: new full-speed USB device number 2 using uhci_hcd
[ 5.529923] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 5.535715] scsi host5: usb-storage 1-2:1.0
[ 5.535852] usbcore: registered new interface driver usb-storage
[ 5.647557] usb 7-2: New USB device found, idVendor=0a5c, idProduct=21e8, bcdDevice= 1.12
[ 5.647565] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.647568] usb 7-2: Product: BCM20702A0
[ 5.647571] usb 7-2: Manufacturer: Broadcom Corp
[ 5.647572] usb 7-2: SerialNumber: 5CF3709E969D
[ 5.931989] usbcore: registered new interface driver uas
[ 6.166514] usb 2-5: new high-speed USB device number 5 using ehci-pci
[ 6.315679] usb 2-5: New USB device found, idVendor=2001, idProduct=3318, bcdDevice= 2.00
[ 6.315686] usb 2-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.315689] usb 2-5: Product: 11ac adapter
[ 6.315691] usb 2-5: Manufacturer: D-Link Corporation
[ 6.315693] usb 2-5: SerialNumber: 00e04c000001
[ 10.955659] usbcore: registered new interface driver btusb
[ 11.090105] usb 2-5: 88XXau f0:b4:d2:b2:73:cf hw_info[107]
[ 11.097531] usbcore: registered new interface driver rtl88XXau

Evo

No123 22.07.2022. 04:07
Citiraj:
Autor tomek@vz (Post 3612920)
Imas kontroler koji sam prekleo 1000 puta. Iskreno - uzmi neki drugi PCI kontroler da nema taj cip na sebi (VIA ne radi probleme).


Alternativno mozes probat:


https://rephlex.de/blog/2021/10/15/l...1-great-again/


Za svaki slucaj daj jos dmesg |grep usb output ovdje.
Ne radi ovo s linka, a kad sam kupovao tu karticu tražio sam onu koja radi na linuxu i za nju je pisalo da radi.

Citiraj:
lspci -nn | grep -i usb
00:1a.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 [8086:3a37]
00:1a.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 [8086:3a38]
00:1a.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 [8086:3a39]
00:1a.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 [8086:3a3c]
00:1d.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 [8086:3a34]
00:1d.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 [8086:3a35]
00:1d.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 [8086:3a36]
00:1d.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 [8086:3a3a]
02:00.0 USB controller [0c03]: Renesas Technology Corp. uPD720201 USB 3.0 Host Controller [1912:0014] (rev 03)

No123 24.07.2022. 06:55
Skinuo sam USB3-201-202-FW-20120615 u kojemu je K2013080.mem i sad ne znam što s tim, nigdje ne mogu naći kako se to instalira.

To bi trebao biti kao neki firmware.

tomek@vz 24.07.2022. 08:05
Citiraj:
Autor No123 (Post 3613316)
Skinuo sam USB3-201-202-FW-20120615 u kojemu je K2013080.mem i sad ne znam što s tim, nigdje ne mogu naći kako se to instalira.

To bi trebao biti kao neki firmware.

Kopiraj ga u /lib/firmware > reboot
Kad sustav boota provjeri sa:


dmesg |grep usb
dmesg |grep firm


dal javlja sta novo.

No123 24.07.2022. 17:40
Citiraj:
Autor tomek@vz (Post 3613319)
Kopiraj ga u /lib/firmware > reboot
Kad sustav boota provjeri sa:


dmesg |grep usb
dmesg |grep firm


dal javlja sta novo.
Ništa! Sve isto.

tomek@vz 24.07.2022. 22:17
Citiraj:
Autor No123 (Post 3613393)
Ništa! Sve isto.

Onda nema vajde od te kartice na Linuxu na zalost.

No123 25.07.2022. 05:04
Našao sam neku s VIA VL805 chipom, valjda će ta raditi.

No123 10.08.2022. 15:09
Evo maloprije stigla kartica Made in PRC sa VIA VL805 čipom i USB 3.0 Stick radi!

No123 12.08.2022. 08:40
Stavio sam grafičku GTS 450 koja ima dva DVI izlaza, a kako imam dva ista monitora spojio sam ih na grafičku.

Kada upalim komp slika se pojavi na jednom monitoru i kada se sustav digne slika se prebaci na drugi monitor, a onaj prvi ode u sleep.

Znači taj prvi je Disabled, kako napraviti da mi oba rade? Imam OpenSuse Tumbleweed Xfce.

tomek@vz 12.08.2022. 09:58
Citiraj:
Autor No123 (Post 3616674)
Stavio sam grafičku GTS 450 koja ima dva DVI izlaza, a kako imam dva ista monitora spojio sam ih na grafičku.

Kada upalim komp slika se pojavi na jednom monitoru i kada se sustav digne slika se prebaci na drugi monitor, a onaj prvi ode u sleep.

Znači taj prvi je Disabled, kako napraviti da mi oba rade? Imam OpenSuse Tumbleweed Xfce.

Pa imas u Settings > Display i poslozi kak hoces.

No123 12.08.2022. 10:03
Citiraj:
Autor tomek@vz (Post 3616695)
Pa imas u Settings > Display i poslozi kak hoces.
Bio sam tamo ali izgleda da to ne radi dobro, ja poklikam ali ne bude tako.

No123 12.08.2022. 15:32
Štos je bio što grafička ima i HDMI izlaz na kojega je bio spojen TV i kada sam isključio TV rade oba monitora.

Nikky 12.08.2022. 15:48
Tu su poznati štosevi:
- kada grafa ima cca 4 - 6 izlaza treba skužit koja 2 ili 3 ili 4 (ovisno o generaciji) mogu biti "različiti ekrani"
- kod tebe je najprije bio štos da se HDMI forsira kao glavni / primarni ekran,
kad si ištekao HDMI TV onda nema te automatike
- sad prođi i definiraj / potvrdi koji će ekran biti primarni, koji sekundarni i za TV da bude klon jednog od to dvoje

No123 13.08.2022. 04:46
Ok, hvala.

No123 14.08.2022. 08:41
Citiraj:
Autor tomek@vz (Post 3612798)
Jer Fedora ima drukciji default slozeni, na OpenSuse moras vise toga rucno slagat. DKMS nije driver za WIFI nego aplikacija koja rekompajlira kernel modul (driver) za novi kernel. Sto se samo drivera tice - najcesce ne trebas driver instalirat nego samo firmware moras iscupat od nekud (jer je propriatery) i lupit u /lib/firmware. Lupi zypper in -y firmware* > reboot i pogledaj dmesg output jel sta javlja za wifi. Drugo pitanje je - dali DKMS uopce sljaka kak spada (imaj na umu i ovo sto je Nino napisao).
Ima u Yastu 8812au driver ali ne radi kada se tamo instalira. Isto tako što sam god probao od onoga što ima na internetu ne radi i onaj 1 click install ne radi. Jedino radi kada instaliram isto kao i na Fedori ali nakon novog kernela moram ponovo instalirati.

rodriguez 14.08.2022. 11:36
Imam linux mint gnome, i nakon zadnjih updateova i kernela kad ga upalim samo crni ekran se pojavi

A htio bi spasit podatke i datoteke pa instalirati Pop_OS

Ivo_Strojnica 14.08.2022. 12:17
I sad kad si razmislija o detaljima filesistema i vidio boot error, sigurno si odlucija to nam sve tu napisati :)

rodriguez 14.08.2022. 12:20
Ne mogu uci u GRUB
Kak da napravim to navedeno? Neznam nist na linuxu

Ivo_Strojnica 14.08.2022. 13:06
u tom slučaju, najjednostavnije ti je bootati sa live CD-a (tipa Pop_OS!), prebaciti se u root i onda pristupiti svom disku.
Mountati ga na neki folder i onda kopirati podatke gdje želiš.

rodriguez 14.08.2022. 13:08
Budem probao, thx Ivo

No123 16.08.2022. 03:53
Citiraj:
Autor No123 (Post 3617060)
Ima u Yastu 8812au driver ali ne radi kada se tamo instalira. Isto tako što sam god probao od onoga što ima na internetu ne radi i onaj 1 click install ne radi. Jedino radi kada instaliram isto kao i na Fedori ali nakon novog kernela moram ponovo instalirati.
Jutros se dogodilo čudo, instaliram novi kernel i WiFi ostane, nisam morao ponovo instalirati driver za DWA-172. :chears:

Nick7 17.08.2022. 09:34
Citiraj:
Autor No123 (Post 3617363)
Jutros se dogodilo čudo, instaliram novi kernel i WiFi ostane, nisam morao ponovo instalirati driver za DWA-172. :chears:
DKMS ftw! ;)

Sent from my Redmi K20 using Tapatalk


Sva vremena su GMT +2. Sada je 00:32.
Stranica 58 od 151 « Prva 84854555657 58 5960616268108 Zadnja »
Show 40 post(s) from this thread on one page

Powered by vBulletin®
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
© 1999-2024 PC Ekspert - Sva prava pridržana ISSN 1334-2940
Ad Management by RedTyger